Please Log In

Forgot your password?

Hop on board...

Are you a new Customer? Click here to register.

Loading Zoom, please wait

Square Dish with Flat Base Mould 8366 (11.3cm x 11.3cm)

Price £13.80 Inc VAT£11.04 Inc VAT (£9.20 ex VAT)up to20% off

3.3 out of 5 stars (3 Customer Reviews)
 Go Back to Square Moulds 

All prices include VAT.

Stock Status: More than 10 in stock
We Also Recommend for Square Dish with Flat Base Mould 8366 (11.3cm x 11.3cm):
Product Information
Square Dish with Flat Base  

The circular flat base makes this a perfect candle dish. Ideal for a festive piece at the dinner table. Makes a nice soap dish too.

Inner Dimensions: Length: 11.3 cm, Width: 11.3 cm, Height: 1.2 cm 
Outer Dimensions: Length: 11.3 cm, Width: 11.3 cm, Height: 1.6 cm 
Base Dimensions: Diameter: 4.4 cm

Fits in all the kilns we sell.

Please note that all our moulds are hand-made and therefore the dimensions may vary slightly from those shown. Mould manufacturers allow a tolerance of up to 2cm. We strongly recommend cutting the glass to the size measured from the actual mould rather than relying solely on the dimensions shown.

Will this mould fit in my kiln?

Try the Elegant Candle Holder mould too.

Firing Schedule:

Please Read: This firing recommendation has been calculated using Bullseye Glass with a thickness of 6 mm in a Paragon GL24 kiln. 

Segment Rate (C/hr) Temp. Hold
1 167C 677C 1:30
2 999 482C 1:00
3 56C 371C :00


  • Small kilns may require the process temperature reducing. In the Hobbyfuser and HotStart Pro, reduce the top temperature from 677C to 654C. In the Firebox 14, reduce the top temperature from 677C to 634C. All kilns vary, as does glass viscosity. Testing is necessary.

  • Remove the shelf when slumping in small kilns.

  • Side firing kilns may require more time in the first ramp than top firing kilns.

  • Bubbles in slumping are caused by firing too high or holding too long at process temperature.

  • Cracked moulds or cracked glass is caused by firing too fast in the first ramp or cooling too fast.

  • Devitrification on the outside of a slumped piece is caused by firing too high or holding too long at process temperature.

All our moulds are designed for multiple use and with care should last for many firings.

Product Reviews
3.3 out of 5 stars
4 out of 5 stars Saturday 25 March, 2017 By anne stuart
This mould has lovely proportions. It does take some effort to find the best firing schedule for your kiln. It has taken me three attempts using a Firebox 14 to achieve a satisfactory result, although the central depression is still soft rather than crisp. I am keeping extensive records especially about the different combinations of glass used to improve or at least maintain these results.
3 out of 5 stars Wednesday 29 July, 2015 By Robert Trethowan
Just as the review before, I followed the procedure as per the slump settings, which were for my Kiln, and although it slumped into the main area, the candle recess was not defined, also the base didn't flatten enough, I fitted 4 base clear rubber feet, and it was ok, I think just a normal square 11cm x 11cm would be just as good, if not better.

WARM GLASS RESPONSE: Sometimes it takes a little experimentation to find the right firing schedule for your particular piece. As a starting point we would suggest using the firing schedule on this product page (assuming you are using Bullseye Glass at 6mm thickness) as it is specific to this mould, rather than your kiln's standard slump settings. Take note too of the troubleshooting tips. Please call us if you continue to have a problem.
3 out of 5 stars Friday 29 May, 2015 By Jade
Makes a nice dish, but isn't 12x12. It's more like 11.5, so you have to cut to down or you'll get a weird overhang.

The ones I've made so far haven't had the central centre make an impression, I'm not sure why.

Still a nice mould.

Write a review

Registered office: 5 Havyat Park, Wrington, Bristol, BS40 5PA, UK
Company Reg No. 5365166. VAT No. 791350132