Kilncare Deluxe-fuser Glass Kiln - FREE MAINLAND UK DELIVERY

Shelf Kit (Optional):

2 x shelves with props. Each shelf is 49cm x 49cm

Kiln Shelf Information
Shape	2 x Squares
Length x Width (or Diameter)	49 x 49cm per shelf
Biggest Circle (Diameter)	49cm per shelf
Biggest Square	49 x 49cm per shelf
Number of 10cm Coasters	32
Diagram

Alternatively you can have one larger shelf of 91cm x 45cm, but this gives less total shelf area than the two smaller shelves. Please contact us if you would prefer this option.

Specifications:

This kiln requires the installation of a circuit breaker.  This should be fitted by a qualified electrician. We recommend you check the power supply to your kiln's location is suitable before purchasing.

• Internal Size (WxDxH): 1020mm x 520mm x 320mm 
• External Size (WxDxH):1420mm* x 890mm x 1300mm*
• Power Rating: 9kw
• Power Supply: single phase or 3-phase and neutral (240V/ 415V N). This kiln will all run on either single phase or three phase as standard and can be changed at any time simply by removing or adding a special link bar (that is provided with the kiln) to the mains connections. This should be done by a qualified electrician.
• Kiln does not come with cable but this can be purchased from us at £10 per metre – on request.
• requires a 50 or 63 amp breaker when connected to single phase (your electrician can advise you)
• Maximum Temperature: 960?C
• Quartz tube "infra-red" heating system
• stainless steel chamber and base
• lid gas spring lift assist
• Automatic, programmable vents
• recessed floor
• heavy duty walkmesh under floor metalwork
• fast react thermocouple
• fast cooling
• Weight: 240kg (270kg with kiln shelf kit)
• Average Firing Cost: £3.15

• Will fit through minimum door width of 90cm (with minor disassembly)

*external width increases to 1550mm when the KCR32 floor mounting bracket is used.

*height increases to 1330mm when the optional automatic vents are fitted

Other Details:

• The Deluxe-fuser is on lockable castors.

• The lid seal is not stuck on but is held in by a removable stainless steel picture frame and as such, in the event of damage, it is fully replaceable leaving a factory fitted finish that will give years more trouble free use.

• Each Deluxe-fuser is fired to 800c with its own KCR32 programmer before dispatch to ensure perfect operation, calibration and removal of most of the binder vapours that are released by all kilns on the first firing.

• Deluxe-fuser kilns carry a 4 year guarantee on all parts including elements.

• Fully complies with all European and CE requirements.

• Shelf kit is optional.

• Kilns contribute towards our discount programme but do not qualify to receive discounts. 

Kiln Details:

Elements:

The kiln is equipped with high performance, hard-wearing infra-red quartz elements and well-designed insulation. It has a fast react thermocouple and is also fast cooling. The elements are located in the lid for even heating; this also makes them easy to replace if required.  The elements are switched off when the lid is opened by an automatic safety switch.

Lid:

The kiln lid has two vents. The vents are closed with Stainless Steel vent flaps which are lined with insulation pads with an anti-dust covered surface for clean operation. Vents are extremely helpful to release moisture (for example when drying a mould at the beginning of the cycle) and if you wish to crash-cool the kiln. 

Optional Extra - Automatic Control of Vents: An optional extra with this kiln, these roof vents are motorised. They can be programmed via the controller to open or close at any point through the firing cycle or at the end of a firing cycle when the last 150C or so need to be shifted before the kiln can be opened.  It could make the difference between coming in to a kiln that can be unloaded in the morning, or one that has still got 3 or 4 hours of cooling before it can be opened.  The vents can also be automatically opened at the start of a crash cool then closed before annealing begins.

Shown in the above picture is Kilncare's unique vented stainless steel roof construction which vastly aids cooling of the kiln.

The lid stays open once lifted, leaving you with both hands free to load or unload the kiln.  There is a handle across the whole front of the kiln making it easy for either left or right hand lifting and a catch to hold the lid closed.

On the front of the lid are two large spy/vent hole with spring return, anti dust flap - great for keeping an eye on your firing.

The boards that make up the chamber are specially produced for Kilncare and are pre-fired to 1100c before inserted into the kiln to remove any shrinkage or warping that could otherwise happen.

Ultra Stable, Fast Cooling Floor Design

Under the floor is where the Deluxe-fuser excels. Under the brickwork, the floor structure is made from heavy duty walk mesh that expands with heat without distorting, offering superb physical strength. It also breathes so, as with the roof of the kiln, it aids cooling dramatically.

The bricks are easily replaced if required as they are not cemented in.

Controller

Delivery:

Delivery is kerbside only and does not include installation. Please consider that you may need help to situate the kiln. The kiln will be delivered boxed on a pallet measuring 145cm x145cm x 145cm and weighing approximately 238kg.

Delivery is free to Mainland UK. Additional charges may apply if there is restricted access to property.

When your kiln is ready for delivery, we’ll contact you to book in a date that is convenient for you. Deliveries are Monday - Friday and someone will need to be available at the premises to take delivery of the kiln. We are unable to specify a delivery time until the morning of the scheduled delivery.

Deliveries outside the UK: Delivery charges vary. While we subsidise delivery costs where we can, for some destinations we may have to request an extra delivery charge in addition to the one calculated at checkout. If this is the case we will contact you as soon as possible to agree this with you, and always before the kiln is dispatched. 

Delivery is currently 6-8 weeks

Will fit through minimum door width of 90cm (with minor disassembly - see page 5 of the kiln manual).